TTSIM-2
TRACETEK TTSIM-2 is a primary sensor interface module with capacity to monitor up to 150 m (500ft) of sensor cable. Output is via3-digit leak…
Thermocable
Water and Fuel Leak Detection Systems
Sensing cable and monitoring modules for water and non-conductive liquids — locating leaks before they reach anything energised.
Brand overview
Water and Fuel Leak Detection
This range covers sensing cable, probes and monitoring modules for both water and non-conductive liquids such as fuel and oil. Water-sensing cable detects where conductors are bridged; fuel-sensing cable responds to hydrocarbons that would not trigger a water system at all.
Monitoring modules and touch-screen alarm panels report the condition of each run and, on locating systems, the distance to the detected point. Intech surveys the route, installs and maintains the range.
- Water and hydrocarbon sensing Separate cable types for conductive and non-conductive liquids.
- Probes for sumps and tanks Point probes where a defined collection point exists.
- Monitoring and alarm modules Run status, fault reporting and distance-to-leak where fitted.
- Interfaces out To BMS, alarm panels and valve isolation where the design calls for it.
Featured
Featured Detection Products
Which cable, probe and module combination suits depends on the liquid and the layout.
TT1000-7.5M / 25FT-PC / TT1000–15M / 50FT–PC
TraceTek sensing cables detect the presence of water at any point along their length. Installed with a TraceTek alarm and locating module, the cable…
TT-FLAT Probe
TraceTek TT FLAT PROBE (TT-FLAT PROBE) is a special purpose probe designed to detect water leaks in specific locations. It is intended to be floor or…
System
How the System Is Put Together
01
Select the sensing type
Water-sensing or hydrocarbon-sensing cable, or a point probe.
02
Route it to the risk
Laid along pipework, tank bunds and the low points of the space.
03
Monitor
The module watches each run and reports condition and location.
04
Alarm and isolate
Local and remote alarm, with valve isolation where specified.
Applications
Where These Systems Are Specified
Anywhere a leak would reach energised equipment, irreplaceable contents or the environment before anybody noticed.
Data centres and server rooms
Raised floors, CRAC units and chilled water pipework.
Industry detailUPS and battery rooms
Where water reaching energised equipment causes an outage.
Industry detailLaboratories and clean areas
Process and purified water distribution.
Industry detailArchives and storage
Irreplaceable records below pipework or plant.
Industry detailHotels and commercial plant
Riser and plant room pipework above occupied space.
Industry detailBasements and service voids
Low points where ingress collects unnoticed.
Industry detailOur services
Water & Fuel Detection System Supply, Installation and Support
Product selection and consultation
Choosing the right model for the application rather than the catalogue.
System design and engineering
Layout, sizing and the cause-and-effect where the system drives something.
Installation and commissioning
Installed, commissioned and proven as one tested sequence.
Upgrades and expansion
Extending or replacing an existing installation without starting again.
Preventive maintenance and AMC
Scheduled inspection and testing with a documented record.
Troubleshooting and support
Fault diagnosis from the team that commissioned the system.
Resources
Water & Fuel Detection System Datasheets
Every datasheet we hold for the range, linked directly. 6 documents.
Full range
The Complete Water & Fuel Detection System Range We Supply
Models & variants
TTSIM-2
TRACETEK TTSIM-2 is a primary sensor interface module with capacity to monitor up to 150 m (500ft) of sensor cable. Output is via3-digit leak location, relay contacts and serial data.
Technical datasheetTT1000-7.5M / 25FT-PC / TT1000–15M / 50FT–PC
TraceTek sensing cables detect the presence of water at any point along their length. Installed with a TraceTek alarm and locating module, the cable senses water intrusion, triggers an alarm, and pinpoints the location.
Technical datasheetTT-FLAT Probe
TraceTek TT FLAT PROBE (TT-FLAT PROBE) is a special purpose probe designed to detect water leaks in specific locations. It is intended to be floor or tray mounted, using either screw or adhesive attachment. The unit has an orange color to promote visibility in the installed location.
Technical datasheet
TT5000
TT5000 is a fuel sensing cable that can detect and locate spills of gasoline, jet fuel, diesel, crude oil and similar hydrocarbon liquids. It will not detect or react to water. The cable is available in outdoor (above ground), underground and indoor versions.
Technical datasheet
TT5000-HUV
TRACETEK TT5000-HUV is a fuel sensing cable that can detect and locate spills of gasoline, jet fuel, diesel, crude oil and similar hydrocarbon liquids. It will not detect or react to water. The TT5000-HUV cable is designed for use on aboveground pipe, around pump pads or valves where cable will be exposed to sunlight and weather during its service life.
Technical datasheet
TT7000-HUV
TRACETEK TT7000 is a strong acid sensor. It responds to concentrated sulfuric and nitric acid. It can be installed outdoors in sunlight and rain or costal environments and resist environmental factors while retaining the ability to detect and locate acid leaks. 1101, 11th floor Technocity IT Premises co-op Society, Sector X-5/3, TTC Industrial Area, Mahape Navi Mumbai 400710 All Rights Reserved By Intech Fire & Security Pvt Ltd.
Technical datasheetFAQ
Frequently Asked Questions
What project teams usually ask about Water & Fuel Detection System.
Still have a question?
Speak directly with one of our fire safety engineers.
Call +91 88795 33000What is the difference between water and fuel sensing cable?
Water-sensing cable responds to a conductive liquid bridging its conductors. Fuel-sensing cable responds to hydrocarbons, which would not trigger a water system.
When would I use a probe instead of cable?
Where there is a defined collection point — a sump, a bund or a tank interstice — a point probe is simpler than running cable.
Does it report where the leak is?
Locating systems do. Whether that is worth it depends on the length of run and how costly searching would be.
Can it interface with our BMS?
Yes, where the module and BMS support a compatible interface. We confirm that against the installed equipment.
Can it isolate automatically?
Where the design includes it, the system can drive valve isolation as well as alarming.
Does Intech install and maintain it?
Yes — route survey, installation, commissioning with a simulated leak test, and AMC.
Genuine product, direct OEM support
Detect Leaks Before They Reach Anything Critical
Tell us which liquid and which space and an engineer will specify the sensing type and quote installation.